Weider Pro 4850 831.153932 Bedienungsanleitung

WEIGHT SYSTEM EXERCISERUser’s ManualPatent PendingCAUTIONRead all precautions and instruc-tions in this manual before usingthis equipment. Save this m

1014. Open the parts bag labeled “ARM ASSEMBLY.”Press three 40mm x 50mm Inner Caps (21) into theLeg Lever (10). Attach the Eyebolt (116) to the LegLev

18.Locate and open the parts bags labeled “CABLEASSEMBLY” and “PULLEYS.”Lubricate the M10 x 165mm Bolt (95) with grease.Attach the Swivel Cage (76) to

1220. Remove the preattached 90mm Pulleys (78)from the Small Pulley Plates (31).Wrap the Swivel High Cable (74) over a 90mmPulley (78). Attach the Pul

1324. Remove the preattached 90mm Pulleys (78)from the Offset Double “U”-bracket (61).Wrap the Swivel Cable (17) around a 90mm Pulley(78). Attach the

1429. Wrap the Lat Cable (88) around a 90mm Pulley(78). Attach the Pulley and a Long Cable Trap (102)to the Top Frame (6) with an M10 x 50mm Bolt(100)

153536383734. Remove the preattached 90mm Pulleys (78)from the Double “U”-bracket (62).Wrap the Butterfly Cable (69) under a 90mm Pulley(78). Attach t

1641. Remove the preattached 90mm Pulley (notshown) from the “U”-bracket (64).Attach the end of the Leg Lever Cable (75) to the“U”-bracket (64) with a

1745. Wrap the Swivel Low Cable (72) under a 90mmPulley (78). Attach the Pulley to the indicated brack-et on the Long Base (106) with an M10 x 45mmBol

1849. Wrap the Swivel Low Cable (72) over a 90mmPulley (78). Attach the Pulley and a Cable Trap (68)between the lower set of holes in the “U”-bracket(

1953. Wrap the Squat Cable (73) under a 90mm Pulley(78). Attach the Pulley and a Cable Trap to the sec-ond set of holes from the top in the indicated

2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2057. Attach the Seat (16) to the Seat Frame (8) with twoM6 x 16mm Screws (114), an M6 x 65mm Screw(99), and an M6 Washer (97).58. Attach the Butterfl

216161. Turn the Squat Backrest (35) so that the four screwholes are closer to the bottom of the SquatBackrest than the top. Attach the Squat Backrest

22ADJUSTMENTSThe instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual t

23ADJUSTING THE SQUAT ARM OR SWIVELCARRIAGETo adjust the height of the Squat Arm (32), first turnthe Adjustment Knob (115) on the Squat Bracket (37)co

HIGH PULLEY(lbs.)1425384861688096101112122LOW PULLEY(lbs.)1425364460708091104111122LEGLEVER(lbs.)2235536791111122148160184190BUTTERFLYARM(lbs.)1726364

25TROUBLESHOOTING Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immedi-ately. The weight sys

26CABLE DIAGRAMSThe cable identification chart below shows the ends of each cable and the lengths of the cables. The cable dia-grams on this page and

27Leg LeverCable (75)Swivel LowCable (72)113245679234123458Swivel Cable (17)

Cable Clip (83)90mm Pulley (78)(Not shown to scale)"V"-pulley (55)(Not shown to scale)115mm Pulley (119)(Not shown to scale)M10 Nylon Locknu

M10 x 20mm Bolt (13)M10 x 60mm Bolt (18)M10 x 70mm Bolt (85)M10 x 95mm Bolt (92)M10 x 45mm Bolt (93)M10 x 85mm Bolt (96)M10 x 165mm Bolt (95)M10 x 50m

IMPORTANT PRECAUTIONS31.Read all instructions in this manual and inthe accompanying literature before using theweight system.2. It is the responsibili

50mm x 75mm Inner Cap (58)40mm x 50mm Inner Cap (21)25mm Round Inner Cap (29)50mm x 70mm Inner Cap (34)38mm Square Inner Cap (67)50mm Square Inner Cap

PART LIST—Model No. 831.153932 R0404ANote: “#” indicates a non-illustrated part. Specifications are subject to change without notice. If a part is mis

465732891012161091091919202021212011621232432333311111135373839394242434347454445444848495050114114525255555657575758641156768102727273741775757811978

Part No. 194013 R0404A Printed in China © 2003 Sears, Roebuck and Co.FULL 90 DAY WARRANTYFor 90 days from the date of purchase, if failure occurs due

4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height:81 in.Width: 96 in. Length: 57 in. Squat Knee RestCurl PadLow Pulley StationHigh Pulley StationLat BarS

5ASSEMBLYMake sure that you have the following tools:• Two adjustable wrenches• One standard screwdriver• One phillips screwdriver• One rubber mal

1.Locate and open the parts bags labeled “FRAMEASSEMBLY 1” and “FRAME ASSEMBLY 2.”See the inset drawing.Attach the Base Cap (24) tothe Short Base (2)

4. Press a 38mm Square Inner Cap (67) into thesquare tube on the Butterfly Upright (3).Slide the Butterfly Upright (3) onto the two indicatedM10 x 65m

87. Press a 50mm x 75mm Inner Cap (58) into the topof the Squat Upright (4). Press two 25mm RoundOuter Caps (120) onto the Upright. Slide the Squat Up

99. Attach a Roller (39) between the indicated set ofholes in the Squat Slider (38) with an M8 x 85mmBolt (94) and an M8 Nylon Locknut (86) as shown.D