USER'S MANUALQUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If you havequestions, or find there are m
1015. Route the Long Cable (23) around the “V”-Pulley (6) on the Right Arm (48). Be surethat the Cable is in the groove of the “V”-Pulley and that the
11CABLE ASSEMBLY19. Note: This assembly step shows how tocomplete the assembly of several pre-attached parts.The 5/8” x 9/16” Spacer (73) has been pre
1221. Route the Short Cable (58) around the 3 1/2”Pulley (15) attached to the lower hole in theFront Upright (42). See the inset drawing.Be sure that
24. Attach the end of the Short Cable (58) to theLong “U”-Bracket (57) with a 1/4” Nylon Lock-nut (2) and a 1/4” Flat Washer (10). Do notcompletely ti
1426. Attach the Backrest (41) to the Front Upright(42) with two 1/4” x 2 1/2” Screws (43) andtwo 1/4” Flat Washers (10).27. Press a 1 1/2” Square Inn
1529. Rest the Seat Frame (36) on the indicated pinin the Front Upright (42). Attach the SeatFrame to the Front Upright with a 5/16” x2 3/4” Carriage
1631. Remove the decals from the decal sheet (not shown) and apply them to the home gym system in the loca-tions shown below.HIGH PULLEYBUTTERFLY8510B
17ADJUSTMENTThe instructions below describe how each part of the home gym system can be adjusted. Refer to the exerciseposter accompanying this manual
18ATTACHING AND REMOVING THE SEATSet the bracket on the Seat Frame (36) onto the indi-cated pins on the Front Upright (42). Attach the SeatFrame to th
19TROUBLESHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. Thehome gym
2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20CABLE DIAGRAMThe cable diagram below shows the proper routing of the Short Cable (58) and the Long Cable (23). Use thediagram to be sure that the tw
21NOTES
22Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. PART LIST—Model No. WESY85104 R1102AKey No. Qty. De
231111885527121544157123272144213616035615122575821355114192651256463769213341276515714110433216507427506216970697047484445444513403837183228303410224
5/16" Nylon Locknut (3)1/4" Flat Washer (10)5/16" Flat Washer (8)3/8" Flat Washer (9)1/4" x 2 1/2" Screw (43)5/16"
1" Retainer (69)3/8" x 2" Bolt (12)3/8" x 3 1/2" Bolt (16)3/8" x 2 1/2" Bolt (7)3/8" x 3 3/4" Bolt (71)3
1" Round Inner Cap (49)1" Round Cover Cap (70)3/4" Round Inner Cap (34)1/2" x 3/4" Spacer (61)1" Round Inner Cap (78)1 1
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6
3WARNING: To reduce the risk of serious injury, read the following important precautionsbefore using the home gym system.IMPORTANT PRECAUTIONSWARNING:
4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 76 in.Width: 38 in. Length: 53 in. Foot PlateLow Pulley StationHigh Pulley StationLat BarLeg LeverButte
5ASSEMBLY156High Side ofBracket355151141274Before beginning assembly, carefully read thefollowing information and instructions:• Place all parts of th
6FRAME ASSEMBLY2. Slide the Front Upright (42) onto the 5/16” x2 1/2” Carriage Bolts (1) in the Base (4).Hand tighten a 5/16” Nylon Locknut (3) ontoea
7FRAME ASSEMBLYARM ASSEMBLY5. Press the Weight Tube Bumper (64) into theend of the Weight Tube (63). Insert theWeight Tube into the stack of Weights (
8ARM ASSEMBLY8. Press a 1 3/4” Square Inner Cap (44) into thetop of a Press Arm (46). Press a 1” RoundInner Cap (49) into each end of the handle onthe
9CABLE ASSEMBLY11.During steps 11 through 25, refer to theCABLE DIAGRAM on page 20 of this manualto verify proper cable routing. Before begin-ning thi
Kommentare zu diesen Handbüchern