Weider 740 Bedienungsanleitung

®USER’S MANUALModel No. WESY74091Serial No. The serial number is found in thelocation shown below. Write theserial number in the space above.CAUTIONRe

1012. Locate the parts bag labeled “CABLE ASSEMBLYAND PULLEYS.” For cable identification and rout-ing during steps 12 through 27, refer to the CableDi

1116. Attach the loop at the end of the Short Cable (58) tothe Weight Tube (63) with a 5/16” x 1 1/2” Bolt (11)and a 5/16” Nylon Locknut (3).163635811

1219. Remove the pre-attached Pulleys (15) from the PulleyBracket (57).Wrap the Butterfly Cable (76) around a 3 1/2” Pulley(15) in the direction shown

1324. Wrap the Long Cable (23) around a 3 1/2” Pulley (15)in the direction shown. Attach the 3 1/2” Pulley (15) and a Cable Trap (66) tothe indicated

1427. Hook the closed loop on the end of the Long Cable(23) onto the 3/8” Eyebolt (35) that is mounted on theLeg Lever (29). Tighten the 5/16” Nylon L

1530. Press a 3/4” Round Inner Cap (34) into each end ofthe Pad Tube (28). Insert the Pad Tube (28) through the indicated hole inthe Leg Lever (29). S

16Long Cable (23)21678534Cable ID Chart58, 126 1/4”76, 87 1/2”23, 233”

Attaching the Lat Bar to the Pulley StationAttach the Lat Bar (54) to the Short Cable (58) with aCable Clip (53).Adjusting the Arms for Butterfly or P

18Tightening the CablesWoven cable, the type of cable used on the home gymsystem, can stretch slightly when it is first used. If thereis slack in the

19ICON of Canada Inc.900 de l’IndustrieSt-Jérôme, QuébecCanada, J7Y 4B8PLACESTAMPHEREPress Butterfly Pulley LegWeight Arm Arm Station LeverPlates (

2Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Ordering Replacement PartsTo order replacement parts, simply call our Customer Service Department toll-free at 1-888-936-4266, Mondaythrough Friday, 8

WESY74091 R0101ANote: Assembly is divided into three stages: 1) frame assembly; 2) armassembly; 3) cable, pulley, and seat assembly. The hardware for

1/4" Flat Washer (10)5/16" Flat Washer (8)3/8" Flat Washer (9)3/8" Nylon Locknut (21)1/4" Nylon Locknut (2)3/8" Nylon Ja

1" Retaining Ring (69)3/8" x 2" Bolt (12)3/8" x 3" Bolt (72)3/8" x 2 3/4" Bolt (71)3/8" x 1 3/4" Bolt (68

1" Round Inner Cap (49)1" Round Cover Cap (70)3/4" Round Inner Cap (34)1 1/2" Square Outer Cap (27)1" Square Inner Cap (65)3/

81REMOVE THIS PART LIST/EXPLODEDDRAWING FROM THE MANUAL

Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Part List—Model No. WESY74091

5354313169706970477474485210 25210 21621225676595956227617777732777373777768151278222212 12236115515405844441544448999957682215226015153517 626158262

3WARNING: Before beginning this or any exercise program, consult your physician. Thisis especially important for persons over the age of 35 or persons

4ASSEMBLED DIMENSIONS: Height: 75 in.Width: 31 in. Length: 44 in. WeightStackLeg LeverButterfly/PressArmFoam RollerSeatBackrestThank you for selecting

5Note: This introduction will save you moretime than it takes to read it.Identifying PartsTo help you identify the small parts used in assem-bly, we h

6Frame Assembly1. Before beginning assembly, make sure you haveread and understood the information on page 5.Locate and open the parts bag labeled “FR

73. Attach the two Weight Bumpers (19) to the Stabilizer(5) with two #8 x 1” Screws (18).Slide the six Weights (25) onto the two tubes on theWeight G

866. Attach the two tubes on the Weight Guide (62) to theTop Frame (55) in the following manner: Slide a 5/16” x 6” Bolt (7) through one of the tubes

999. Identify the Right Arm (48) and the Left Arm (47) byimagining yourself sitting on the seat. Note the posi-tion of the welded bracket (A) on each