Weider WESY49202 Bedienungsanleitung

QUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If youhave questions, or find that thereare missing or dama

1015. See the inset drawing. Attach the MilitaryPress Arm (84) to the Pivot Arm (101) withtwo M8 x 55mm Bolts (33) and two M8 NylonLocknuts (3).Press

1117. Attach the Left Pull-up Arm (75) and the RightPull-up Arm (77) to the Assist Upright (74)with two M8 x 70mm Bolts (11) and two M8Nylon Locknuts

1220. Wrap the High Cable (58) around a “V”-Pulley(50). Attach the Pulley and a Long Cable Trap(31) to the indicated bracket on the FrontUpright (42)

1324. See the inset drawing. Attach a 90mm Pulley(15) and a Cable Trap (66) to the upper hole ina Long “U”-Bracket (57) with an M10 x 50mmBolt (12) an

1427. Locate the Low Cable (23). Route the LowCable under a 90mm Pulley (15). Attach thePulley to the M10 x 95mm Bolt (not shown) inthe Press Frame (1

1531. Attach the end of the Low Cable (23) to theLong “U”-Bracket (57) with an M8 NylonLocknut (3) and an M8 Washer (8). Do notcompletely tighten the

1634. Wrap the Military Press Cable (72) around a“V”-Pulley (50). Attach the Pulley to the TopFrame (55) with an M10 x 55mm Bolt (86)and an M10 Nylon

1736. Slide an M8 Washer (8) onto an M8 x 75mmBolt (93). Insert the Bolt through the indicatedhole in the Pivot Arm (101). The Bolt mustbe inserted fr

1838. Locate the Leg Press Cable (99). Attach theend of the Leg Press Cable to the Long “U”-Bracket (57) with an M8 Nylon Locknut (3)and an M8 Washer

1940. Locate and open the parts bag labeled“SEAT ASSEMBLY.”Insert an M6 x 60mm Carriage Bolt (92)through the center hole in a Seat Plate (37).Attach t

1. Read all instructions in this manual and inthe accompanying literature before using theweight system.2. It is the responsibility of the owner to en

2043. Attach the Front Backrest (41) to the FrontUpright (42) with two M6 x 65mm Screws (43)and two M6 Washers (10). The Backrest mustbe oriented as s

47. Press two19mm Round Inner Caps (34) intoeach Pad Tube (28). Insert a Pad Tube (28) into the Front SeatFrame (36). Slide a Foam Pad (30) onto eache

22ADJUSTMENTSThe instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual t

23ATTACHING AND REMOVING THE SEATTo attach the Seat (13), set the bracket on the FrontSeat Frame (36) onto the indicated pins on the FrontUpright (42)

24WEIGHT RESISTANCE CHARTThis chart shows the approximate weight resistance at each weight station. “Top” refers to the 6.5 lbs. topweight. The other

TROUBLESHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immedi-ately. T

26CABLE DIAGRAMSThe cable diagrams on these pages show the proper routing of the High Cable (58), the Low Cable (23), theMilitary Press Cable (72), an

27Military Press Cable (72)Leg Press Cable (99)1—Rear Weight Stack234765324—Rear Seat Frame8—Pivot Arm1—Long “U”-BracketMilitary Press Cable (72) and

M8 x 60mm Bolt (22)M8 x 45mm Bolt (24)M8 x 55mm Bolt (33)M10 x 50mm Bolt (12)M10 x 45mm Bolt (76)M10 x 55mm Bolt (86)M6 x 50mm Carriage Bolt (38)M6 x

M8 x 65mm Carriage Bolt (1)M8 x 70mm CarriageBolt (14)M8 x 70mm CarriageBolt (11)M8 x 75mm Bolt (93)M8 x 120mm Bolt (68)M8 x 150mm Bolt (60)M10 x 150m

3BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 78 in.Width: 110 in. Length: 92 in. Foot PlateHigh Pulley StationLat BarLeg LeverButterfly ArmsAssist A

50mm Square Outer Cap (51)25mm Square Inner Cap (6)50mm Square Inner Cap (27)25mm Round Inner Cap (49)45mm Square Inner Cap (44)19mm Round Inner Cap (

PART LIST—Model No. WESY49202 R0103ANote: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty. Desc

602721505586118151244881558214421361622435871365108642526199334962246461639152159232117271410434142213503186706969702147444544454850318613403837183234

ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6

4ASSEMBLY18811512714315151. Before beginning assembly, be sure thatyou have read and understand the infor-mation in the box above.Locate and open the

52. Slide the Assist Upright (74) and the LegPress Upright (56) onto the indicated M8 x65mm Carriage Bolts (1) in the Stabilizer (5).The high side of

64. Press a 50mm Square Inner Cap (27) into theend of the Top Frame (55). Press a 45mmSquare Inner Cap (44) into each end of thecrossbar on the Top Fr

77. Press a Weight Tube Bumper (64) into theend of the Short Weight Tube (108). Insert theWeight Tube into the front stack of Weights(25). Be sure tha

89. Attach the upper ends of the Short WeightGuides (73) to the Top Frame (55) with an M8 x150mm Bolt (60), two 19.5mm Spacers (61),and an M8 Nylon Lo

912. Press a 25mm Round Inner Cap (49) into oneof the Press Arms (46). Press a 45mmSquare Inner Cap (44) into the Press Arm.Attach the Press Arm (46)