Visit our website atwww.weiderfitness.comnew products, prizes,fitness tips, and much more!CAUTIONRead all precautions and instruc-tions in this manual
1015. Attach the Rear Crossbar (45) to the Left RearUpright (46) with two M10 x 94mm Bolts (18), twoM10 Washers (74), and two M10 Nylon Locknuts(32).
1117. Press a 51mm x 76mm Inner Cap (21) into thetop of a Front Upright (44). Attach an UprightCover (51) to the Front Upright with five M4 x16mm Scre
1220. Route the Cable (79) up through the Lat Tower(48) and over an 89mm Pulley (65). Attach thePulley inside of the Lat Tower with an M10 x75mm Bolt
1324. Route the Cable (79) through the Lat Tower Base(49) and under an 89mm Pulley (65). Attach thePulley to the bracket on the Lat Tower Base withan
1428. Wet the ends of the Lat Bar (59) and the Row Bar(58) with soapy water. Slide four Handgrips (60)onto the ends of the two Bars.29.Make sure that
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 17 for impor-tant information about how to get the most bene
168144796659WEIGHT RESTS AND SAFETY SPOTTERSTo use the barbell (not shown) with the weight rack,first move the Weight Rests (55, 80) and the SafetySpo
17EXERCISE GUIDELINESTHE FOUR BASIC TYPES OF WORKOUTSMuscle BuildingTo increase the size and strength of your muscles,push them close to their maximum
18Rest for a short period of time after each set. Theideal resting periods are:• Rest for three minutes after each set for a musclebuilding workout. •
19MONDAYDate: / / EXERCISE WEIGHT SETS REPSEXERCISE WEIGHT SETS REPSEXERCISE WEIGHT SETS REPSAEROBIC EXERCISEAEROBIC EXERCISETUESD
2WARNING DECAL PLACEMENTWARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
M10 x 68mm Bolt (26)M10 x 45mm Bolt (27)M10 x 100mm Bolt (28)M10 x 75mm Bolt (30)M10 x 86mm Bolt (35)M10 x 19mm Bolt (72)M10 x 78mm Bolt (75)M6 x 16mm
19mm Round Inner Cap (19)50mm Square Inner Cap (22)45mm Square Inner Cap (76)38mm x 50mm Inner Cap (77)20mm x 40mm Inner Cap (20)51mm x 76mm Inner Cap
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back coverof the user’s manual for informatio
816880686060595860661234566127891011131514141616171717172222222319197878393922222222212618262830293136292973733175343434343461613737373737742727323232
Part No. 202676 R0204A Printed in China © 2004 ICON Health & Fitness, Inc.LIMITED WARRANTYICON Health & Fitness, Inc. (ICON), warrants this pr
1. Read all instructions in this manual beforeusing the weight bench. Use the weightbench only as described in this manual. 2. It is the responsibilit
ASSEMBLED DIMENSIONS: Height: 84 in.Width: 67 in. Depth: 75 in. 4Weight CarriageFront UprightSafety SpotterWeight RestStorage TubeBackrest BracketRigh
5Before beginning assembly, carefully read thefollowing information and instructions:•Assembly requires two people.• Place all parts in a cleared area
65.Attach the Backrest (10) to the Backrest Frames(6) with four M6 x 53mm Bolts (29) and four M6Washers (37). Note: If the four Bolts cannot beinserte
31373229301576. Press four Bushings (34) into the BackrestFrames (6) as shown. Secure the Backrest Knob (25) to the BenchFrame (2). Pull the Knob out
89. Press three 50mm Square Inner Caps (22) intothe Leg Lever (7). Press a 48mm Round InnerCap (23) into the tube on the Leg Lever.Slide the two Pad T
912. Attach the left side of the Front Crossbar (43) tothe Base (42) with two M10 x 94mm Bolts (18), aLarge Joint Plate (41), and two M10 NylonLocknut
Kommentare zu diesen Handbüchern