Weider WEBE1996 Bedienungsanleitung

Model No. WEBE1996.2Serial No.Write the serial number in thespace above for future reference.CAUTIONRead all precautions and instruc-tions in this man

1010. Apply a small amount of grease to an M10 x95mm Button Bolt (73).Pull the Long Adjustment Knob (37) out as faras it will go. Insert the bracket o

1112. Set the Foot Plate (19) on the Top Tube (16)and the Bottom Tube (17). Finger tighten fourM4 x 25mm Screws (60) through the Tubes intothe Foot Pl

1215. Slide a Front Ankle Brace (22) onto the roundtube on the Lock Frame (11). Next, press a19mm Round Cap (45) into the round tube, andattach the Ro

1318. Attach a Handle (12) to the Left Frame (4) withtwo M10 x 80mm Button Bolts (52), two M10Curved Washers (50), and two M10 Locknuts(65).Attach the

14This section explains how to adjust the inversion system. See DEVELOPING A PROGRAM on page 17 forimportant information about how to get the most ben

15LEVELING THE INVERSION SYSTEMIf the inversion system rocks slightly on your floor,turn one or both of the Leveling Feet (41) until theinversion syst

16This section explains how to rotate back on the inversion system, and then return to the starting position. Beforeusing the inversion system, see th

17BENEFITING FROM USING THE INVERSIONSYSTEMIf you feel nauseated while using the inversion sys-tem, return to the starting position. Note that it mayt

18PART LIST—Model No. WEBE1996.2 R1209A11 Left Base21Right Base31Center Base41Left Frame51Right Frame61Center Frame Extension71Center Frame81Backrest

EXPLODED DRAWING—Model No. WEBE1996.2 R1209A1234567891011121213141516171819202134342222232425262728293031323270323369393840404141424242743744444645454

2WEIDER is a registered trademark of ICON IP, Inc.WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Part No. 294312 R1209A Printed in China © 2009 ICON IP, Inc.LIMITED WARRANTYIMPORTANT: You must register this product within 30 days of the purchase d

3WARNING: To reduce the risk of serious injury, read all important precautions andinstructions in this manual and all warnings on your inversion syste

4HandleLeft FrameLong Adjustment KnobBackrestHeadrestFoot PlateAnkle BraceAnkle LockIndex HandleShort Adjustment KnobRight FrameASSEMBLED DIMENSIONS:H

5M10 Locknut (65)M8 Locknut (72)M6 Washer (62)M10 x 85mm Button Bolt (51)M10 x 95mm Button Bolt (73)M6 x 18mmButton Screw (55)M6 x 60mm Button Screw (

61.Press a 63mm Round Cap (40) onto the LeftBase (1).Attach a Foot (42) to the Left Base (1) with anM4 x 20mm Screw (71). Next, tighten aLeveling Foot

73. Attach the Support Leg (13) to the Center Base(3) with three M10 x 35mm Button Bolts (53)and three M10 Locknuts (65).Attach the Base (14) to the C

86. See the inset drawing. Identify the CenterFrame (7).Apply some of the included grease to both sidesof the Left Large Spacer (31).Attach the Left L

98. Attach the Top Cover (23) and the BottomCover (24) to the Center Frame (7) with two M4x 16mm Screws (58) and an M4 x 30mm Screw(63).Attach the Cen